Start with the aviation industry

Chapter 67
the next day.

Early in the morning, Lin Feng came to the side of the imported five-axis machine, and said loudly: "Today we process the whole turbine disk."

Hu Xiaoxiao said, "Master, you are talking about these three things, right?"

Lin Feng nodded, "Little Ma, tidy up the table and wipe it clean."

When the master spoke, Ma Xiaoli carried it out unconditionally. She cleaned up the work table next to the machine tool and wiped it with a rag.

Lin Feng spread out the design drawing of the whole turbine disk on the table, and put the milling cutters brought down on the work table.

"Wow, so complicated!"

Seeing the design drawings, Hu Xiaoxiao was surprised, and said a little worriedly, "Master, we are not sure about such a difficult part."

Lin Feng said confidently, "What are you afraid of, I have everything to do with you."

So, the master instructed the two apprentices to start making preparations for processing.

First of all, install the jig on the worktable of the machine tool, and then install the milling cutter in the tool magazine of the machine tool. Hu Xiaoxiao and Ma Xiaoli are completely capable of doing these things, and Lin Feng does not need to do it himself.

The three masters are making preparations before processing.

Factory building, conference room.

The military, the Phoenix Factory, and the Phoenix Institute held a meeting. This was a tripartite meeting. The topic of the meeting was the processing and manufacturing of parts required for the design verification of a new type of missile engine.

The design has entered the verification stage, some components need to be manufactured, and then a series of verification work will be carried out in the laboratory of Phoenix Institute.

Such as strength verification, such as performance verification, such as fatigue verification, life verification and so on.

The manufacturing of relevant parts is mainly undertaken by Phoenix Factory. After three or four 10 minutes of the meeting, Zeng Zhihong mentioned the processing and manufacturing of the overall turbine disk again.

"Everyone, let me tell you some good news. The integral turbine disk has started to be processed in workshop 406, and it should be ready for processing now."

Wang Tianfang also confirmed, "Relevant pre-processing preparations are already underway, and at this time, processing may be about to begin."

Zhang Fenjin, the general manager of this type of missile, said, "We have already arranged what should be arranged just now, and we have almost discussed what should be coordinated. Why don't we go to workshop 406 to have a look at the processing of this whole turbine disk."

As the general manager of this type of missile, why does he care so much about the processing of this part?

Because this is the first time that a milled integral turbine disc has been used for precision casting before, and it is also the first time that a new type of turbine blade design has been used. This part has a great impact on the performance improvement of the missile engine.

Facing Zhang Fenjin's proposal, Wang Tianfang said: "I think it's okay, we can go there now."

Everyone got up one after another, and a group of more than a dozen people left the factory building, and entered the 406 workshop not long after.

This movement is a little louder.

Not only were there many people, but each of them had different identities, whether they were factory leaders, leaders of the Phoenix Institute, or people from the military.

As soon as a group of people walked into the production site of workshop 406, they immediately attracted the attention of many people, whether it was the workers at the production site, or the technicians and managers.

Even some busy workers stopped temporarily, stretched their necks, and looked at them.

"Wow, it looks like they are all big leaders."

"That's Mr. Wang, and that's Director Meng."

"Oh my god, the representatives of the general army and the deputy general army are here."

There was a slight commotion in the entire production site. Lin Feng was instructing the two apprentices to perform some pre-processing operations, and suddenly noticed this situation.

Hu Xiaoxiao even said, "Master, there are a lot of people, look, they are coming towards us."

Lin Feng nodded slightly, seeing this group of people walking towards this side under the leadership of Wang Tianfang, he understood what was going on.

Eighty percent of them are here to take a look at the processing of this part.

This overall turbine disc is very important to the leaders.Lin Feng thought so in his heart.

"Kobayashi, how are the preparations going?"

A few meters away, Wang Tianfang asked.

Lin Feng hurriedly said, "Hi Mr. Wang, hello leaders, we are in the process of pre-processing preparations, basically ready, just need to set the knife and find the alignment, and then we can start processing."

Everyone has also seen that the parts to be processed on the machine table have been clamped, and Lin Feng is holding the control handle in his hand, and it seems that he is going to set the tool and align it.

Tool setting before processing and part alignment are very important and critical. Given the importance and difficulty of processing this part, Lin Feng originally planned to do it himself.

Lin Feng still planned to do the processing of the first piece himself.

Wang Tianfang looked at the parts on the machine table, nodded in satisfaction, and introduced, "This is a craftsman from our 406 workshop, a very good guy."

Being praised in front of so many leaders, Lin Feng was a little embarrassed, and quickly showed humility.

Among these leaders, a small number of people know Lin Feng, and a small number of people have heard of Lin Feng's name. After all, Lin Feng's performance in the previous period can be described as amazing.

Most of the leaders didn't know Lin Feng. After hearing Wang Tianfang's introduction, they were slightly shocked.

I originally thought that Lin Feng was an operator, but I didn't expect that he was actually a craftsman.

Machine tool operation, parts processing, etc., aren't operators doing the work? Why is this craftsman so powerful and seems to be very skilled in operation.

what!
He was actually setting the knife and looking for the correct parts. It seemed that he was going to process the first piece himself.

Omg this is awesome!

Although they often went deep into the manufacturing site, it was really the first time to see a process technician so proficiently operating an imported five-axis linkage CNC machine tool.

Under everyone's surprised gazes, Lin Feng aligned the knife and aligned the parts. After feeling that there was no problem, he put down the control handle in his hand and closed the safety door of the machine tool.

"Mr. Wang, you can start processing!"

Wang Tianfang waved his hand: "Start processing."

Lin Feng pressed the start button, the machine tool started to work, the spindle moved quickly and positioned precisely with a "swoosh", the milling cutter rotated at high speed, a large amount of milky white coolant was sprayed out from the coolant nozzle, and the milling cutter began to mill parts.

The blade is thin and silent.

This corn milling cutter designed by Lin Feng himself accurately cuts into the part, the metal is milled, and the metal chips fall on the workbench, and then are washed into the metal chip collecting bucket below.

Everyone is basically an insider.

As long as you look at the processing situation, you can basically understand the truth. Some people nodded slightly.

Zhong Zimin had been in the Phoenix factory for a long time, and he was considered an expert. After a few glances, he felt that this processing seemed unusual, so he hurriedly took a closer look.

After looking through the glass safety door, he made a request, "Xiao Lin, start the metal chip conveyor belt of the machine tool, I want to have a look at the metal chips that have been milled."

Some people wondered why Mr. Zhong made such a request.

(End of this chapter)